精品国产一区二区-精品国产一区二区三区19-精品国产一区二区三区www-精品国产一区二区三区不卡-精品国产一区二区三区不卡在线

(1) Set the tool offset amounts and parameters before proceeding the program restart search. If they are not set
beforehand, the axes will not return to the proper machining start position.
(2) Attempting the automatic start up during the restart search causes "T01 Cycle start prohibit 0111" and it will
not start up automatically.
(3) The axes will not return to the proper machining start position if a program using the user macro external signa
input, machine coordinate readout or external mirror image command executes the restart search.
(4) If an attempt was made to shift the coordinate systems by manual or MDI interrupt the last time the machining
program was being executed, the axes will not return to the position where the coordinate system was shifted
whether it restarts with type 1 or type 2.
(5) When using the type 1, a top search for the head of the program is not available.
Restart search of the type 1 searches from the previous operation start block and locates the designated block
as it memorizes the operation start block previously operated.
(6) When "#8914 Auto Top search" is set to "0" for the type 2, an error message "Top search not completed" will
be displayed if the search is attempted directly with the type 2 without executing the top search.
Conduct the top search first.
(7) The macro statement blocks cannot be searched .
It is possible to execute the restart search if the control parameter "#8101 MACRO SINGLE" is set to ON.
However, note that the tool path may change because of the radius compensation, the corner R/C, and
geometric read ahead blocks.
(8) When executing the restart for the type 1 with a tape, the axes will not return to the proper machinig start
position if the opearation starts from midway of the tape.
(9) WHILE/GOTO statement cannot be used for a tape operation. Thus, if a restart search is executed with the
tape operation which includes WHILE/GOTO statement, a program error (P295) will occur.
(10) A search error will occur if an intended ONB is not found even M99 block is detected in the main program.
伺服馬達 HA-LFS701MB
PLC FX3U-128MT/ESS
SSCNET Ⅲ 光纖 MR-J3BUS30M-B
伺服控制器 MR-J2S-15KB
編碼器用電纜 MR-EKCBL5M-H
PLC FX3G-40MR/ES-A
伺服馬達 HA-LFS11K1M4
編碼器接頭 MR-ENCNS
視頻/RGB輸入單元 GT16M-V4R1
多路轉(zhuǎn)換模塊 A60MXRN
存儲卡 FX2N-ROM-E1
CC-Link接口單元 MR-J2S-T01
PLC FX2N-32MT-D
編碼器電纜 MR-JCCBL2M-H
多媒體單元 GT16M-MMR
PLC FX3U-32MT/ESS
PLC FX3U-80MR/ES-A
PLC FX1S-14MT-D
PLC FX1N-24MT-D
接線端子塊 MR-TB20
PLC FX1S-20MR-001
電源連接器 MR-PWCNS3
編碼器電纜 MR-ENCBL20M-H
伺服控制器 MR-J2S-11KB
附件 MR-J2HBUS1M
PLC FX3G-60MR/ES-A
電磁制動器用電纜 MR-BKS1CBL5M-A1-H
視頻輸入單元 GT16M-V4
接頭套件 MR-ECN3
伺服控制器 MR-J2S-22KB