精品国产一区二区-精品国产一区二区三区19-精品国产一区二区三区www-精品国产一区二区三区不卡-精品国产一区二区三区不卡在线

ems related to product and manual
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by
the machine tool builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added. Refer to the specifications
issued by the machine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool.
Some screens and functions may differ depending on the NC system (or its version), and some function
may not be possible. Please confirm the specifications before use.
ems related to operation
Before starting actual machining, always carry out graphic check, dry run operation and single block
operation to check the machining program, tool compensation amount, workpiece compensation amoun
and etc.
If the workpiece coordinate system offset amount is changed during single block stop, the new setting wi
be valid from the next block.
Turn the mirror image ON and OFF at the mirror image center.
If the tool compensation amount is changed during automatic operation (including during single block
stop), it will be validated from the next block or blocks onwards.
ems related to programming
The commands with "no value after G" will be handled as "G00".
";" "EOB" and "%" "EOR" are expressions used for explanation. The actual codes are: For ISO: "CR, LF", o
"LF" and "%".
Programs created on the Edit screen are stored in the NC memory in a "CR, LF" format, but programs
created with external devices such as the FLD or RS-232C may be stored in an "LF" format.
The actual codes for EIA are: "EOB (End of Block)" and "EOR (End of Record)".
When creating the machining program, select the appropriate machining conditions, and make sure that
the performance, capacity and limits of the machine and NC are not exceeded. The examples do not
電磁制動器用電纜 MR-BKS1CBL10M-A1-H
伺服電機電源用電纜 MR-PWS2CBL03M-A2-L
PLC FX1S-20MR-DS
Q系列編程器SRAM卡用電池 Q3MEM-BAT
PLC FX1N-60MR-D
PLC FX1S-14MT-DSS
編碼器電纜 MR-JHSCBL2M-L
伺服電機電源用電纜 MR-PWS1CBL5M-A1-H
閃存卡 QD81MEM-8GBC
伺服電機電源用電纜 MR-PWS1CBL10M-A1-L
編碼器接頭 MR-J2CNM
電磁制動器用電纜 MR-BKS1CBL10M-A2-H
伺服電機電源用電纜 MR-PWS1CBL10M-A1-H
可編程控制器 FX1N-14MR-001
MES接口模塊 QJ71MES96
編碼器用電纜 MR-EKCBL2M-H
伺服電機電源用電纜 MR-PWS1CBL5M-A1-L
PLC FX2NC-96MT-DSS
編碼器電纜 MR-JCCBL5M-H
伺服驅動器 MR-J2S-40B
定位模塊 FX2N-20GM
存儲卡 FX-RAM-8
存儲器盒 FX3U-FLROM-64
PLC FX3U-128MT/ESS
編碼器用電纜 MR-ENECBL2M-H
GT16觸摸屏 GT1675M-VTBD
可編程控制器 FX1N-60MR-001
伺服放大器 MR-J2S-70B
PLC FX2N-128MT-001
伺服馬達 HA-LFS15K1M